Development on Press Thermal Processless Plate Negative CTP Plate
Application
EcooGraphix ECOO-G is a new, environmentally friendly, Development On Press CTP plate.
It can be run directly on a printing press after imaging, without a need for chemical processing.
Recommended application to press procedures of ECOO-G:
1. Clean all the inks on the blanket;
2. Start the press machine, apply the water roller, run 30-40 seconds;
3. Apply the ink rollers 20-30 seconds;
4. Apply the paper and start print.
Remark: If steps 2 and 3 are longer, the paper will be wasted less.
Specification
Model
ECOO-G
Plate Type
Thermal-negative type
Application
High-grade commercial and newspaper printing
Substrate
Electrolyte graining and Anodized AL substrate
Thickness
0.15mm/ 0.30mm
Maximum short grain width
Maximum width 1280 mm
Spectrum scope
800-850 nm
Photosensitive wavelength
830 nm
Platesetter
Various dominant thermal platesetters in the market
Coating color
Grey
Low-energy imaging
130-150 MJ/cm²
The period of latent image stabilization
≤ 7 days
Recommended screen method
1-99% @200 LPI AM or 20μm FM or mixture
The paper number of start-up
< 50 sheets
Safety light
4 hours under yellow light;
1 hour under a fluorescent lamp;
Direct exposure under natural light is safe but not recommended.
Processing
Without processing, directly on the press
Run Length
100,000 impressions; Actual run length depends on printing conditions
Shelf life
12 months under recommended condition
Transportation
Packed in seal and stored using prevention from light, moisture, overheating, and high humidity.
| Model | ECOO-G |
| Plate Type | Thermal-negative type |
| Application | High-grade commercial and newspaper printing |
| Substrate | Electrolyte graining and Anodized AL substrate |
| Thickness | 0.15mm/ 0.30mm |
| Maximum short grain width | Maximum width 1280 mm |
| Spectrum scope | 800-850 nm |
| Photosensitive wavelength | 830 nm |
| Platesetter | Various dominant thermal platesetters in the market |
| Coating color | Grey |
| Low-energy imaging | 130-150 MJ/cm² |
| The period of latent image stabilization | ≤ 7 days |
| Recommended screen method | 1-99% @200 LPI AM or 20μm FM or mixture |
| The paper number of start-up | < 50 sheets |
| Safety light | 4 hours under yellow light; 1 hour under fluorescent lamp;
Direct exposure under natural light is safe but not recommended. |
| Processing | Without processing, directly on the press |
| Run Length | 100,000 impressions;
Actual run length depends on printing conditions |
| Shelf life | 12 months under recommended condition |
| Transportation | Packed in seal and stored using prevention
from light, moisture, overheating, and high humidity |
| Storage | Recommended condition: 18ºC-24ºC, 40%-50% RH. |
Applied parameters in the Imaging device
CTP model
Data | Kodak
trendsetters | LOTTEM 400(TH1.7) | MAGNUS 400 | Screen 8600S |
| Laser power | 15-17W | 300-320mw | 19.5-21.5W | 80-90 % |
| Drum speed | 250-300rpm | 850-900rpm | 400-450rpm | 800-900rpm |
| Resolution | Customized | Customized | Customized | Customized |
| Parameter that needs set up | Focus/ Zoom | Focus/ Zoom | Focus/ Zoom | Focus/ Zoom |
*Note: Higher exposure energy will make the image contrast clear, and benefit the plate run length;
while over-high/low exposure energy will affect the image quality negatively.
ECOO-G Processless CTP plate Video: https://youtu.be/LLqNaY1ivcI
Characteristics
ECOO-G is a double layer, and the emulsion layer will not dissolve in water,
so it will not integrate into the fountain solution;
while the protection layer is well water-soluble, and it will be easily dissolved into the fountain solution.
Customer Feedback
Producing And Packaging
From production to delivery, we make every detail very carefully to guarantee
the good product quality and service to customers.
FAQ
Q1: Can I get the sample?
A: We are very glad to provide some samples for you to test. We usually provide 5-15 pieces of plates for free, but sincerely hope to get your kind support for the air courier freight. This cost can be returned to you in your first order.
Q2: What is the cost for the CTP plate sample freight?
A: The air freight depends on the packing size and weight, and the delivery destination. Or you can arrange the pick-up service from your local agent.
Q3: How long can the sample be ready?
A: It usually takes about 3 days to prepare the sample.
Q4: Can I visit your factory?
A: You are warmly welcome to visit our factory! Our company is in Hangzhou city, which is about 1.5 hours by train from Shanghai.
Q5: How many square meters of CTP plates can feed one 20' container?
A: About 20000-25000sqm.
Q6: Can I take my brand and label on the packing?
A: Yes, we can provide the OEM with the customer's brand and label.
Product Tags:
|
|
Processless Aluminum DOP Thermal CTP Plate 0.30mm For Offset Printing Images
|
